View HA-2600883_277755.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HA-2600/883 HA-2602/883
July 1994
Wideband, High Impedance Operational Amplifiers
Description
HA-2600/883 and HA-2602/883 are internally compensated bipolar operational amplifiers that feature very high input impedance coupled with wideband AC performance. The high resistance of the input stage is complemented by low offset voltage (4mV max at +25oC for HA-2600/883) and low bias and offset current (10nA max at +25oC for HA-2600/ 883) to facilitate accurate signal processing. Offset voltage can be reduced further by means of an external nulling potentiometer. The 4V/s minimum slew rate at +25oC and the minimum open loop gain of 100kV/V at +25oC enables the HA-2600/883 to perform high gain amplification of fast, wideband signals. These dynamic characteristics, coupled with fast settling times, make these amplifiers ideally suited to pulse amplification designs as well as high frequency or video applications. The frequency response of the amplifier can be tailored to exact design requirements by means of an external bandwidth control capacitor. Other high performance designs such as high gain, low distortion audio amplifiers, high-Q and wideband active filters and high speed comparators, are excellent uses of this part.
Features
* This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. * High Input Impedance (HA-2600/883). . . . 100M (Min) 500M (Typ) * High Slew Rate . . . . . . . . . . . . . . . . . . . . . . . 4V/s (Min) 7V/s (Typ) * Low Input Bias Current (HA-2600/883). . . . 10nA (Max) 1nA (Typ) * Low Input Offset Current (HA-2600/883) . . . 4mV (Max) * Wide Unity Gain Bandwidth . . . . . . . . . . . 12MHz (Typ) * Output Short Circuit Protection
Applications
* Video Amplifier * Pulse Amplifier * High-Q Active Filters * High Speed Comparators * Low Distortion Oscillators
Ordering Information
PART NUMBER HA2-2600/883 HA7-2600/883 HA2-2602/883 HA7-2602/883 TEMPERATURE RANGE -55oC -55oC -55oC to to to +125oC +125oC +125oC PACKAGE 8 Pin Can 8 Lead CerDIP 8 Pin Can 8 Lead CerDIP
-55oC to +125oC
Pinouts
HA-2600/883, HA-2602/883 (CERDIP) TOP VIEW HA-2600/883, HA-2602/883 (METAL CAN) TOP VIEW
COMP BAL -IN +IN V1 2 3 4 + 8 7 6 5 COMP BAL V+ OUT BAL -IN 2 + 3 4 V5 6 OUT 1 8 7 V+
+IN
BAL
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright (c) Intersil Corporation 1999
Spec Number
3-181
511005-883 File Number 3700
Specifications HA-2600/883, HA-2602/883
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current . . . . . . . . . . . . . . .Full Short Circuit Protection Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
Thermal Information
Thermal Resistance JA JC CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W 28oC/W Metal Can Package . . . . . . . . . . . . . . . . . 160oC/W 75oC/W Package Power Dissipation Limit at +75oC for TJ +175oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625mW Package Power Dissipation Derating Factor Above +75oC CersDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mW/oC
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V VINCM 1/2 (V+ - V-) RL 2k
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 1 2, 3 +IB VCM = 0V, +RS = 100k, -RS = 100 VCM = 0V, +RS = 100, -RS = 100k VCM = 0V, +RS = 100k, -RS = 100k V+ = +4V, V- = -26V 1 2, 3 1 2, 3 1 2, 3 1 2, 3 -CMR V+ = +26V, V- = -4V 1 2, 3 Large Signal Voltage Gain +AVOL VOUT = 0V and +10V, RL = 2k VOUT = 0V and -10V, RL = 2k VCM = +10V, V+ = +5V, V- = -25V, VOUT = -10V VCM = -10V, V+ = +25V, V- = -5V, VOUT = +10V RL = 2k 4 5, 6 4 5, 6 1 2, 3 1 2, 3 4 5, 6 -VOUT RL = 2k 4 5, 6 HA-2600/883 TEMPERATURE +25oC +125oC, -55oC MIN -4 -6 -10 -30 -10 -30 -10 -30 11 11 100 70 100 70 80 80 80 80 10 10 MAX 4 6 10 30 10 30 10 30 -11 -11 -10 -10 HA-2602/883 MIN -5 -7 -25 -60 -25 -60 -25 -60 11 11 80 60 80 60 74 74 74 74 10 10 MAX 5 7 25 60 25 60 25 60 -11 -11 -10 -10 UNITS mV mV nA nA nA nA nA nA V V V V kV/V kV/V kV/V kV/V dB dB dB dB V V V V
PARAMETERS Input Offset Voltage Input Bias Current
SYMBOL VIO
CONDITIONS VCM = 0V
+25oC +125oC, -55oC
-IB
+25oC +125oC, -55oC
Input Offset Current Common Mode Range
IIO
+25oC +125oC, -55oC
+CMR
+25oC +125oC, -55oC
+25oC +125oC, -55oC
+25oC +125oC, -55oC
-AVOL
+25oC +125oC, -55oC
Common Mode Rejection Ratio
+CMRR
+25oC +125oC, -55oC
-CMRR
+25oC +125oC, -55oC
Output Voltage Swing
+VOUT
+25oC +125oC, -55oC
+25oC +125oC, -55oC
Spec Number 3-182
511005-883
Specifications HA-2600/883, HA-2602/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 4 5, 6 -IOUT VOUT = +10V 4 5, 6 Quiescent Power Supply Current +ICC VOUT = 0V, IOUT = 0mA 1 2, 3 -ICC VOUT = 0V, IOUT = 0mA 1 2, 3 Power Supply Rejection Ratio +PSRR VSUP = 5V, V+ = +10V, V- = -15V, V+ = +20V, V- = -15V VSUP = 5V, V+ = +15V, V- = -10V, V+ = +15V, V- = -20V Note 1 1 2, 3 1 2, 3 1 2, 3 -VIOAdj Note 1 1 2, 3 NOTE: 1. Offset adjustment range is [VIO (Measured) 1mV] minimum referred to output. This test is for functionality only to assure adjustment through 0V. HA-2600/883 TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC MIN 15 10 -3.7 -4.0 80 80 80 80 VIO-1 VIO-1 VIO+1 VIO+1 MAX -15 -10 3.7 4.0 HA-2602/883 MIN 10 7.5 -3.7 -4.0 74 74 74 74 VIO-1 VIO-1 VIO+1 VIO+1 MAX -10 -7.5 3.7 4.0 UNITS mA mA mA mA mA mA mA mA dB dB dB dB mV mV mV mV
PARAMETERS Output Current
SYMBOL +IOUT
CONDITIONS VOUT = -10V
-PSRR
Offset Voltage Adjustment
+VIOAdj
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 50, RLOAD = 2k, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. GROUP A SUBGROUPS 7 8A, 8B -SR VOUT = +5V to -5V 7 8A, 8B Rise and Fall Time TR VOUT = 0 to +200mV 10% TR 90% VOUT = 0 to -200mV 10% TF 90% VOUT = 0 to +200mV 7 8A, 8B 7 8A, 8B 7 8A, 8B -OS VOUT = 0 to -200mV 7 8A, 8B HA-2600/883 TEMPERATURE +25oC +125oC, -55oC MIN 4 3 4 3 MAX 60 70 60 70 40 50 40 50 HA-2602/883 MIN 4 3 4 3 MAX 60 70 60 70 40 50 40 50 UNITS V/s V/s V/s V/s ns ns ns ns % % % %
PARAMETERS Slew Rate
SYMBOL +SR
CONDITIONS VOUT = -5V to +5V
+25oC +125oC, -55oC
+25oC +125oC, -55oC
TF
+25oC +125oC, -55oC
Overshoot
+OS
+25oC +125oC, -55oC
+25oC +125oC, -55oC
Spec Number 3-183
511005-883
Specifications HA-2600/883, HA-2602/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = 15V, RLOAD = 2k, CLOAD = 50pF, Unless Otherwise Specified. HA-2600/883 PARAMETERS Differential Input Resistance Full Power Bandwidth Minimum Closed Loop Stable Gain Output Short Circuit Current SYMBOL RIN FPBW CLSG +ISC CONDITIONS VCM = 0V VPEAK = 10V RL = 2k, CL = 50pF VOUT = 1V, RL = 10 NOTES 1 1, 2 1 1 1 1 -ISC VOUT = -1V, RL = 10 1 1 1 Quiescent Power Consumption NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2VPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.) TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS Interim Electrical Parameters (Pre Burn-In) Final Electrical Test Parameters Group A Test Requirements Groups C and D Endpoints NOTE: 1. PDA applies to Subgroup 1 only. SUBGROUPS (SEE TABLES 1 AND 2) 1 1 (Note 1), 2, 3, 4, 5, 6, 7, 8A, 8B 1, 2, 3, 4, 5, 6, 7, 8A, 8B 1 PC VOUT = 0V, IOUT = 0mA 1, 3 TEMPERATURE +25oC +25oC -55oC to +125oC +25oC +125oC -55oC +25 C +125oC -55oC -55oC to +125oC
o
HA-2602/883 MIN 40 50 1 -50 -45 -60 MAX 50 45 60 120 UNITS M kHz V/V mA mA mA mA mA mA mW
MIN 100 50 1 -50 -45 -60 -
MAX 50 45 60 -
120
-
Spec Number 3-184
511005-883
HA-2600/883, HA-2602/883 Die Characteristics
DIE DIMENSIONS: 69 x 56 x 19 mils 1 mils 1750 x 1420 x 483m 25.4m METALLIZATION: Type: Al, 1% Cu Thickness: 16kA 2kA GLASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.) Silox Thickness: 12kA 2kA Nitride Thickness: 3.5kA 1.5kA WORST CASE CURRENT DENSITY: 3.9 x 104A/cm2 SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: HA-2600/883: 140 HA-2602/883: 140 PROCESS: Bipolar Dielectric Isolation
Metallization Mask Layout
HA-2600/883, HA-2602/883
+IN -IN
BAL
V-
COMP
BAL
V+
OUT
Spec Number 3-185
511005-883

▲Up To Search▲

Price & Availability of HA-2600883

	To Download HA-2600883 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .